Book An Estimate Now

 

Have you been trying to locate help and advice concerning Installing A Bathtub?

Setting up a bathtub isn't specifically rocket science, however it does require strong plumbing, woodworking, as well as sometimes, tiling abilities. Changing an old bathtub with a new one is also a reasonably challenging job. If the old bathtub is readily accessible, the job can move speedily; if you need to open a wall to get rid of the old tub and also place the new bathtub, the job is much harder. In either instance, the job is within a residence handyman's skills, although you will require an assistant to move out the old tub and also set in the new one. Make certain you have certified on your own for the job and also fit attempting it. As opposed to hiring a contractor to take control of a halfway-completed task, it is better to consider utilizing one before you start. Possibilities are you may require a specialist plumber to make tube links.
This write-up will aid you mount a new tub in your washroom if you have currently purchased a brand-new bathtub and don't require to transform the setup of your previous supply of water pipes.
Your devices and also material list must comprise the following:

 

• New Tub


• Hammer


• Pipeline Wrenches


• Prybar


• Shatterproof glass


• Degree


• Pliers


• Adjustable Wrench


• Putty Blade


• Screwdriver


• Cold Knife


• Measuring tape


• Pipeline Caps


 

Removing Old Touches

If you need to replace old taps with brand-new ones as a part of your setup, after that the first thing you ought to do is separate the supply of water. After doing so, activate the taps to drain any water continuing to be in the system. The procedure of eliminating the existing faucets can be rather problematic due to the limited accessibility that is frequently the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipelines to the taps. Have a fabric ready for the staying water that will certainly come from the pipelines. As soon as the supply pipes have actually been removed, utilize the same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to quit the single taps from transforming during this procedure. When the taps have been eliminated, the holes in the bath/basin will certainly need to be cleansed of any old sealing compound.
Prior to moving on to fit the brand-new faucets, contrast the pipeline links on the old faucets to the new faucets. If the old taps are longer than the new taps, then a shank adapter is needed for the new taps to fit.

 

 

Fitting New Touches

If the tails of the new faucets are plastic, then you will require a plastic connector to prevent damage to the thread. One end of the port fits on the plastic tail of the tap as well as the other end offers a connection to the current supply pipelines.
If you need to fit a monobloc, after that you will need reducing couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next, position the tap in the installing hole in the bath/basin making certain that the washing machines are in place in between the tap and also the sink. Protect the tap in place with the maker supplied backnut. As soon as the faucet is firmly in position, the supply pipelines can be connected to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with regular tap connectors. The former kind should be linked to the faucet finishes initially, tightening up just by hand. The supply pipelines can later be connected to the other end. Tighten both ends with a spanner after both ends have actually been connected.

 

 

Installing the Bath tub

Making use of both wooden boards under its feet, position the bathtub in the required setting. The wood boards are useful in uniformly spreading the weight of the bath tub over the area of the boards rather than concentrating all the weight onto four small points.
The next objective is to make sure that the bathtub is leveled all round. This can be accomplished by examining the level as well as changing the feet on the bath tub up until the spirit level reviews level.
To set up faucets, fit the bottom of the outermost adaptable tap connector to the ideal supply pipeline by making a compression sign up with; then do the very same for the various other faucet.
Turn on the water supply as well as check all joints as well as brand-new pipework for leaks and also tighten them if essential. Fill the bath tub as well as likewise examine the overflow outlet and also the normal electrical outlet for leaks.
Ultimately, take care of the bathroom paneling as explained in the maker's instruction manual. Tiling as well as sealing around the bathtub needs to wait up until the bath tub has been used a minimum of when as this will resolve it right into its final position.

 

 

Getting ready for the Setup

First of all, the sustaining framework supplied with the bathroom ought to be fitted (if needed) according to the manufacturer's instructions. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is necessary to see to it that if the tap comes with a plastic washing machine, it is fitted between the bathroom as well as the taps. On a plastic bath, it is also practical to fit a sustaining plate under the taps device to stop strain on the bath tub.
Fit the adaptable faucet ports to the bottom of both taps making use of 2 nuts and olives (in some cases supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet through the hole in the bath. Make use of the nut provided by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. Ensure you make use of all of the supplied washers.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath should currently be ready to be suited its final placement.

 

 

Tiling Around the Bathtub

In the area where the bath fulfills the ceramic tile, it is needed to seal the accompanies a silicone rubber caulking. This is important as the fitting can move sufficient to split a stiff seal, causing the water to pass through the wall in between the bathroom and also the tiling, causing difficulties with moisture and possible leakages to the ceiling listed below.
You can pick from a range of coloured sealers to blend in your components and also installations. They are offered in tubes and also cartridges, and also can securing voids approximately a width of 3mm (1/8 inch). If you have a larger space to load, you can fill it with twists of soaked newspaper or soft rope. Keep in mind to constantly load the tub with water before securing, to enable the activity experienced when the tub is in use. The sealant can break relatively early if you do not take into consideration this activity prior to sealing.
Alternatively, ceramic coving or quadrant tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are likewise easily readily available on the marketplace. It is a good idea to fit the floor tiles using water-resistant or waterproof sticky as well as grout.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

As a devoted reader on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround, I was thinking sharing that excerpt was worthwhile. Sharing is good. Helping people is fun. Thank you so much for going through it.

Book Services